If the computer being woken up is communicating via Wi-Fi, a supplementary standard called Wake on Wireless LAN (WoWLAN) must be used. Equivalent terms contain wake on WAN, remote wake-up, power on by LAN, power up by LAN, resume by LAN, resume on LAN and wake up on LAN. You can also initiate the message from another network by using a subnet directed broadcast or WOL gateway service. Related post: WAN VS LAN: What Is the Difference Between Them? The message is usually sent to the target computer through a program executed on a device (such as a smartphone) connected to the same local area network (LAN). WOL, which is the abbreviation of Wake On Lan, is an industry-standard protocol that supports waking computers up by a network message. And in this post from MiniTool, you can also know its principle of operation, as well as how to enable it. You can see PC 1 will start up after you click it.What is WOL and what can it be used for? It is short for Wake On Lan and can be used to wake computers up from a very low power mode remotely. Then fill in the information like below and click BOOT. Run RemoteBoot app on iPhone from the WAN side. On the RemoteBoot app, the IP will be a domain name you registered with DDNS instead of the WAN IP.Ħ. In this case, you may try to set up the DDNS (Dynamic Domain Name Server) on the router following the FAQ. The WAN IP address is a dynamic IP usually and it may change at any time. Now we check the WAN IP address of the Router PC 1 connected. Open a port for PC 1 by port forwarding function such as virtual server. Set Address reservation for PC 1 on our router.Ĥ. We call it PC 1 here.Ģ.Set IP&MAC binding of PC 1 on our router and enable IP&MAC binding function.ģ. Then Enable ShutDown Wake-On-Lan, Wake on Magic Packet and Wake on pattem match.Īfter the settings are done on the computer, we need to do some setting on our Router.ġ.Check MAC address and IP address of the computer need Wake-on-LAN. Turn on the computer and go to Control Panel- Network and Internet- Network and Sharing Center- Local area connection- Properties- Configure- Advanced. Usually this option is in power management menu.Ģ. Then enable ‘Resume by PCI Device’ and ‘Resume by PCI-E Device’. WakeOnLanGui,LanHelper for Windows or RemoteBoot for IOS.ġ. The mainboard and wired network adapter must support Wake-on-LAN feature. It is also possible to initiate the message from another network by using subnet directed broadcasts or a WOL gateway service. The message is usually sent by a program executed on other devices. Wake-on-LAN (WoL) is an Ethernet or Token ring computer networking standard that allows a computer to be turned on or awakened by a network message. Archer C1200, Archer C5400, Archer A2600, Archer AX55, TL-WR841ND, Archer AX53, Archer C5, Archer AX10, Archer C2, Archer AX51, Archer AX95, Archer AX96, Archer C6U, TL-WR940N, TL-WR1043N, Archer C80, Archer AXE95, Archer C8, Archer AX10000, Archer C3150, Archer C9, Archer AX50, Archer C6, Archer C7, Archer AX90, Archer AX6000, Archer C24, Archer A20, Archer A64, Archer C60, Archer C2600, Archer C21, Archer C64, TL-WR941N, Archer A10 Pro, Archer AX1800, TL-WR941ND, Archer AX80, TL-WR901N, Archer AX206, Archer C59, Archer C58, Archer AX4200, Archer C3200, Archer C900, Archer A2, Archer AX75, Archer AX4400, Archer C3000, Archer AX73, Archer C50, TL-WR941HP, Archer A10, Archer A54, Archer AX4800, Archer C50, Archer C1900, Archer C54, Archer A2300, TL-WR841N, Archer A2600 Pro, Archer A6, Archer A7, Archer AX72, Archer A5, Archer GX90, TL-WR801N, Archer A8, Archer A9, Archer AX68, Archer C2300, Archer AX5300, Archer AX23, Archer AX20, Archer C4000, Archer AX21, Archer AX55 Pro, Archer A3000, Archer C2700, TL-WR841HP, Archer AXE300, Archer AX1500, Archer C90, Archer AX60, Archer AX11000, Archer AX3000
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |